![]() These Terms are divided into “Section A” and “Section B”. (“Giant” and sometimes also referred to as “us,” “we” or “our” herein) via use of or the websites of any Giant affiliates and/or authorized Giant retailers that are linked to the foregoing websites (each a “Website”) (references herein to “this Website” shall mean and apply to each and every aforementioned Website), as well as (B) your USE OF THIS WEBSITE EVEN IF YOU DO NOT MAKE ANY PURCHASE. THESE TERMS AND CONDITIONS (“TERMS”) GOVERN BOTH (A) PURCHASES BY YOU (the “Customer” and sometimes also referred to as “you,” “your,” or “user” herein) from Giant Bicycle, Inc. I will try the delay() for debugging but it will need to be millis() so it doesn't block.ĪlertFlag = sensor.READ THESE TERMS AND CONDITIONS CAREFULLY. This report would have more information with Invalid conversion from 'const char*' to 'char*' Void initButtonUL(Adafruit_GFX *gfx, int16_t x1, int16_t y1, uint16_t w, ![]() Users/admin/Documents/Arduino/libraries/Adafruit_GFX_Library/Adafruit_GFX.h:262:8: error: initializing argument 9 of 'void Adafruit_GFX_Button::initButtonUL(Adafruit_GFX*, int16_t, int16_t, uint16_t, uint16_t, uint16_t, uint16_t, uint16_t, char*, uint8_t)' In file included from /Users/admin/Documents/Arduino/Petal_Stapler/Petal_Stapler.ino:21:0: Petal_Stapler:194:103: error: invalid conversion from 'const char*' to 'char*' Users/admin/Documents/Arduino/Petal_Stapler/Petal_Stapler.ino: In function 'void btnGrid()': Arduino: 1.8.15 (Mac OS X), Board: "Arduino Due (Programming Port)" I tried that late last night and got an error and haven't had time to research the error the compiler gave me. Ty = map(tx, TS_MINX, TS_MAXX, 0, tft.height()) įor (uint8_t b = 0 b < row * col b++) ītn.initButtonUL( &tft, left, top, w, h, RA8875_WHITE, RA8875_RED, RA8875_GREEN, titleStr, 3 ) Tx = map(ty, TS_MAXY, TS_MINY, 0, tft.width()) Ty = map(ty, TS_MAXY, TS_MINY, 0, tft.height()) Tx = map(tx, TS_MAXX, TS_MINX, 0, tft.width()) Ty = map(tx, TS_MAXX, TS_MINX, 0, tft.height()) Tx = map(ty, TS_MINY, TS_MAXY, 0, tft.width()) Ty = map(ty, TS_MINY, TS_MAXY, 0, tft.height()) Tx = map(tx, TS_MINX, TS_MAXX, 0, tft.width()) Serial.print(tx) Serial.print(", ") Serial.println(ty) If (currentMillis2 - startMillis2 >= period2) L_AlertFlag = bitRead(AlertFlag, 0) //grab the low alert field using bitwise operator and save current L_AlertFlagĭigitalWrite(13, LOW) //Logic is reversed from MosfetĭigitalWrite(13, HIGH) //logic is reversed Mosfet H_AlertFlag = bitRead(AlertFlag, 1) //grab the high alert field using bitwise operator and save current to H_AlertFlag If (currentMillis - startMillis >= period)ĪlertFlag = sensor.getHighLowAlert() //read the alert flags from the configuration register If (sensor.dataReady() = true) // Function to make sure that there is data ready to be printed, only prints temperature values when data is ready Tft.textWrite("Choose how many petals you need.") Tft.PWM1config(true, RA8875_PWM_CLK_DIV1024) // PWM output for backlight Tft.GPIOX(true) // Enable TFT - display enable tied to GPIOX tAlertFunctionMode(0) //set to alert mode Serial.println("Device failed to setup- Freezing code.") If (sensor.begin() = true) // Function to check if the sensor will correctly self-identify with the proper Device ID/Address tClock(400000) // Set clock speed to be the fastest for better communication (fast mode) PinMode(19, INPUT_PULLUP) //back proximity sensor (stapler in start position) PinMode(18, INPUT_PULLUP) //front proximity sensor(stapler in position) PinMode(footswitch, INPUT), //program start switch PinMode(fanControl, OUTPUT) //Fan cooling controlĭigitalWrite(fanControl, HIGH) // turn fans off on startup(logic reversed from Mosfet) TMP117 sensor //inialize sensor (I2C 0x48)īyte AlertFlag = 0 //variable to hold high and low alert flags from configuration registerīoolean H_AlertFlag = 0 //variable to hold state of high alert flagīoolean L_AlertFlag = 0 //variable to hold state of low alert flag ![]() I'm trying to get a better understanding what's going when I write code. I added a serial.print underneath the touchRead(&tx, &ty) (in the Void GFXbuttonswitch) and it now works as coded. I have married the two sketches together into one sketch and when I uploaded it to my Arduino the touch events with the TFT would not register to flip the on screen buttons from red to green. I have a TFT and a Temp sensor that I'm putting into my sketch, I have separate sketches for each component and they work as coded. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |